Get 2023 Free NACE NACE-CIP1-001 Exam Practice Materials Collection
Get Latest and 100% Accurate NACE-CIP1-001 Exam Questions
NEW QUESTION 27
A single application coating film has a measured dry film thickness (DFT) between 4 and 5 mils (between 100 and 125 microns). The volume solids of the coating immediately before application were 67%, What wet film thickness (WFT) was applied?
- A. 6 to 7 mils (150 to 175 microns)
- B. 5 to 6 mils (125 to 150 microns)
- C. 10 to 12 mils (250 to 300 microns)
- D. 8 to 10 mils (200 to 250 microns)
Answer: A
NEW QUESTION 28
Most industrial coatings are:
- A. Resistant to temperatures above 200C
- B. Resistant to concentrated sulfuric acid
- C. Inorganic
- D. Organic
Answer: D
NEW QUESTION 29
Inspection documentation is important because:
- A. Owners use the documentation for a variety of purposes
- B. It is the only deliverable item provided by the inspector
- C. a) & b)
- D. a) only
Answer: A
NEW QUESTION 30
Conventional spray is a good choice when:
- A. High production rates are required
- B. High quality finishes are required
- C. High transfer efficiency is required
- D. High viscosity coatings are being applied
Answer: B
NEW QUESTION 31
You are the NACE Inspector on a 5000 sq. ft. job where SSPC PA 2 has been specified.
Assuming all areas are in compliance, how many gauge readings and spot measurements are required?
- A. 225 Gauge Readings resulting in 75 Spot Measurements
- B. 75 Gauge Readings resulting in 25 Spot Measurements
- C. 105 Gauge Readings resulting in 35 Spot Measurements
- D. 45 Gauge readings resulting in 15 Spot Measurements
Answer: A
NEW QUESTION 32
NACE No. 4/SSPC-SP-7 is a joint standard for
- A. near-white metal blast cleaning.
- B. brush-off blast cleaning.
- C. white metal blast cleaning.
- D. commercial blast cleaning.
Answer: B
NEW QUESTION 33
An inspectors personal log book should contain:
- A. No comments regarding the application team
- B. Subjective comments re ding the application team
- C. Objective comments regarding the application work
- D. The inspector's personal opinions of the application team
Answer: A
NEW QUESTION 34
SSPC SP 1 identifies the use of:
- A. Biodegradable detergents
- B. Inorganic solvents
- C. Organic solvents
- D. A wide variety of materials
Answer: D
NEW QUESTION 35
What is used to determine compressed air cleanliness?
- A. Blotter test
- B. Profilometer
- C. Needle pressure gauge
- D. Psychrometer
Answer: B
NEW QUESTION 36
Galvanic corrosion occurs on which of the following substrates:
- A. Fiberglass Reinforced Plastic
- B. Metal
- C. Concrete
- D. Wood
Answer: B
NEW QUESTION 37
The primary difference between Non-Convertible vs. Convertible coatings is:
- A. Non-Convertible coatings cure by co-reaction whereas Convertible coatings do not
- B. Convertible coatings cure solely by solvent evaporation whereas Non-Convertible coatings do not
- C. Convertible coatings do not undergo a chemical change during curing whereas Non-Convertible coatings do
- D. Non-convertible coatings do not undergo a chemical change during curing whereas Convertible coatings do
Answer: D
NEW QUESTION 38
Digital hygrometers
- A. consist of a bimetallic sensing element protected from wind gusts.
- B. determine relative humidity, air temperature, and dew point temperature:
- C. use a thermocouple in contact with the surface to measure temperature
- D. are used to measure temperature from a distance.
Answer: B
NEW QUESTION 39
You are the NACE Inspector on a job where the Owner's specification requites you to perform a twice daily check of blast pressure at the nozzle. It is now day 30 on the job and all of your readings have been within compliance. The Contractor complains that these checks taking up much time and in view of the compliant results they are unnecessary.
Your FIRST preferred course of action is to:
- A. Skip the checks and just record the same readings as you have been getting
- B. Skip the checks as you are. confident the blast pressure is OK
- C. Keep doing the checks regardless
- D. Keep doing the checks and consult the Owner's representative for direction
Answer: D
NEW QUESTION 40
Upon arrival of coating materials, the inspector should
- A. observe aryl document that the applicator WFT at regular intervals during application.
- B. observe and document time frame and environmental conditions between each coat.
- C. review coating contractors' plans for storage of coating materials and confirm they meet national, local and owners' fire and environmental regulations.
- D. observe and document the amount of material and batch numbers.
Answer: D
NEW QUESTION 41
If a Thermoset coating is heated it will:
- A. Soften when heated and retain its softness when cooled
- B. Soften when heated and return to its original hardness when cooled
- C. Harden and retain its hardness when cooled
- D. Harden and return to its original hardness when cooled
Answer: C
NEW QUESTION 42
Stripe coats are generally applied to:
- A. Welds
- B. a), b), and c)
- C. Edges and corners
- D. Complex geometric shapes
Answer: B
NEW QUESTION 43
To be of value the Inspector's documentation must be:
- A. Always typewritten
- B. Submitted before the end of the job
- C. Always handwritten
- D. Timely, accurate and concise
Answer: D
NEW QUESTION 44
You have just received your NACE CIP Level 1 certification when you are asked to supervise a team of uncertified field pipeline inspectors.
Your FIRST preferred course of action is to:
- A. Review the NACE Attestation prior to making a decision
- B. Advise the prospective employer that you cannot accept the position
- C. Accept the assignment without hesitation
- D. Meet with the prospective employer to determine the scope of your role
Answer: D
NEW QUESTION 45
When holiday testing is required the Inspector is always required to enforce NACE SP 0188:
- A. False
- B. True
Answer: B
NEW QUESTION 46
Check abrasive blast pressure close to the
- A. blast nozzle
- B. substrate
- C. blast pot
- D. compressor
Answer: A
NEW QUESTION 47
Check abrasive blast pressure with a
- A. replica tape
- B. nozzle aperature gauge
- C. surface comparator
- D. needle pressure gauge
Answer: D
NEW QUESTION 48
A successful coating inspector must be able to
- A. apply the coating with expert accuracy.
- B. advise the coating applicator on how to mix the coating.
- C. look for problems or issues during application.
- D. recommend the appropriate coating technique for the job to the contractor.
Answer: C
NEW QUESTION 49
Inspector's daily reports are used:
Select All That Apply
- A. To provide continuity between inspectors
- B. To aid in arbitration between the contractor and client
- C. To help in cases of a coating failure
- D. By the contractor to estimate the amount of work done that day
Answer: A,B,C,D
NEW QUESTION 50
......
Maximum Grades By Making ready With NACE-CIP1-001 Dumps: https://testking.prep4sureexam.com/NACE-CIP1-001-dumps-torrent.html