NSE5_FNC_AD_7.6 Exam Dumps Pass with Updated Jul-2026 Tests Dumps [Q15-Q38]

NSE5_FNC_AD_7.6 Exam Dumps Pass with Updated Jul-2026 Tests Dumps

NSE5_FNC_AD_7.6 exam questions for practice in 2026 Updated 61 Questions

NEW QUESTION # 15
When configuring FortiNAC-F to manage FortiGate VPN users, an endpoint compliance policy must be created for the integration.
Why is the endpoint compliance policy necessary for this type of integration?

• A. To confirm the installed endpoint certificate
• B. To designate the required agent type
• C. To validate the VPN user credentials
• D. To validate the VPN client being used

Answer: B

Explanation:
The integration of FortiNAC-F with FortiGate VPN requires a specific policy workflow to bridge the gap between initial user authentication and full network access. When a user connects to the VPN, the FortiGate typically provides the User ID and IP address, but FortiNAC-F requires a MAC address to uniquely identify and manage the endpoint's record.
According to the FortiGate VPN Integration Guide, the Endpoint Compliance Policy is a mandatory component of this setup because it is used to designate the required agent type. Because a VPN connection is Layer 3, FortiNAC cannot "see" the MAC address through traditional SNMP or L2 polling. The compliance policy instructs the system to present a Captive Portal to the remote user, requiring them to download and run either the Persistent or Dissolvable Agent. The agent then reports the device's MAC address back to FortiNAC, allowing the system to correlate the VPN session with a host record.
Once the agent is running and the MAC is known, FortiNAC-F can evaluate the device's security posture (if scanning is configured) and send the necessary FSSO tags back to the FortiGate to lift the initial network restrictions. Without the compliance policy to enforce the agent requirement, the connection would remain in an isolated "IP-only" state with no unique hardware identity.
"The Endpoint Compliance Policy is necessary to control the agent requirement for VPN users. Create a default VPN Endpoint Compliance Policy to distribute an agent via captive portal for isolated machines. This policy allows the administrator to designate the required agent type (Persistent or Dissolvable) that will be used to collect the hardware (MAC) address and perform health scans on the remote endpoint." - FortiNAC FortiGate VPN Integration Guide: Default Endpoint Compliance Policy (Optional) Section.

NEW QUESTION # 16
Which two statements are true about integrating a third-party device using SNMP traps from that device as input to generate an event? (Choose two.)

• A. The sending device must be modeled in the inventory topology.
• B. set allowaccess snmp must be configured using the CLI on the FortiNAC-F receiving interface.
• C. The IP address OID and MAC address OID must be configured in the trap MIB file.
• D. The sending device must support SNMPv3.

Answer: A,B

NEW QUESTION # 17
An administrator wants FortiNAC-F to pass firewall tags to FortiGate to leverage dynamic address groups used in firewall policies. On FortiNAC-F, what determines the values that are passed?

• A. Security rule
• B. Device profiling rule
• C. RADIUS group attribute
• D. Model configuration

Answer: D

Explanation:
The correct answer is A . FortiNAC-F passes firewall tags to FortiGate through Security Fabric integration so FortiGate can use those values as dynamic address groups in firewall policies. The study guide explains that firewall tags are administrator-defined string values and that FortiNAC-F dynamically assigns them based on a security policy or logical network. More specifically for network access enforcement, it states that the network access configuration defines the logical network , and the logical network defines the firewall tag through the device model configuration .
This is the same mechanism used in VPN and Fabric workflows: the FortiGate device model contains the mappings of logical networks to the actual tags or groups that FortiNAC-F sends to FortiGate. The guide states that FortiNAC-F network access policies and logical networks determine the group or tag information, while the FortiGate model configuration contains the mappings used for the values sent.
Option B is not the best answer because a device profiling rule can classify a device and may cause it to match a policy, but it does not directly define the FortiGate tag value sent for policy enforcement. Option C can apply firewall tags in security automation scenarios, but the standard FortiGate dynamic address group mapping is defined in model configuration. Option D is unrelated; RADIUS attributes are used in RADIUS access responses, not FortiGate Fabric tag propagation.

NEW QUESTION # 18
An administrator has created several device profiling rules and evaluated all existing devices in the database.
Some of the devices appear in the profiled devices view because they matched a rule, but they remain unknown and the registration column in the profiled devices view shows " No " .
What is the most likely cause?

• A. The devices match more than one device profiling rule.
• B. The devices have persistent agents installed, and the point of connection has PA optimization enabled.
• C. The confirm device profiling rule option is not enabled.
• D. The device profiling rule has registration set to manual.

Answer: C

Explanation:
In FortiNAC-F,Device Profiling Rulesare used to automatically identify and categorize devices (such as IP cameras, printers, or IoT devices) based on fingerprints like DHCP fingerprints, OIDs, or MAC prefixes.
When a device matches a rule, it appears in theProfiled Devicesview.
However, matching a rule does not automatically register the device in the database unless the rule is configured to do so. If the devices appear in the view but remain " Unknown " and show " No " in the registration column, it indicates that the " Confirm " (or " Auto-register " ) action has not been triggered. In the Device Profiling Rule configuration, there is a setting called " Allow Auto-Approval " or " Confirm " . If this is not enabled, the system identifies the device but waits for an administrator to manually approve the match before changing the host status from " Unknown " to " Registered " .
This is a common " safety " configuration used during the initial deployment phase to ensure that the profiling rules are accurate before the system begins automatically granting network access based on those matches.
" If a device matches a rule but is not registered, check the rule configuration. TheConfirmoption (within the Method or Rule settings) determines if the system automatically registers the device upon a match.
IfConfirmis not enabled, the device will remain in the ' Profiled ' state with a registration status of ' No ' until an administrator manually promotes the device. " -FortiNAC-F Administration Guide: Device Profiling Rules.

NEW QUESTION # 19
Refer to the exhibit.

If a host is connected to a port in the Building 1 First Floor Ports group, what must also be true to match this user/host profile?

• A. The host must have a role value of contractor, an installed persistent agent or a security access value of contractor, and be connected between 6 AM and 5 PM.
• B. The host must have a role value of contractor or an installed persistent agent or a security access value of contractor, and be connected between 6 AM and 5 PM.
• C. The host must have a role value of contractor or an installed persistent agent and a security access value of contractor, and be connected between 6 AM and 5 PM.
• D. The host must have a role value of contractor or an installed persistent agent, a security access value of contractor, and be connected between 9 AM and 5 PM.

Answer: C

Explanation:
The User/Host Profile in FortiNAC-F is the fundamental logic engine used to categorize endpoints for policy assignment. As seen in the exhibit, the configuration uses a combination of Boolean logic operators (OR and AND) to define the "Who/What" attributes.
According to the FortiNAC-F Administrator Guide, attributes grouped together within the same bracket or connected by an OR operator require only one of those conditions to be met. In the exhibit, the first two attributes are "Host Role = Contractor" OR "Host Persistent Agent = Yes". This forms a single logical block. This block is then joined to the third attribute ("Host Security Access Value = Contractor") by an AND operator. Consequently, a host must satisfy at least one of the first two conditions AND satisfy the third condition to match the "Who/What" section.
Furthermore, the profile includes Location and When (time) constraints. The exhibit shows the location is restricted to the "Building 1 First Floor Ports" group. The "When" schedule is explicitly set to Mon-Fri 6:00 AM - 5:00 PM. For a profile to match, all enabled sections (Who/What, Locations, and When) must be satisfied simultaneously. Therefore, the host must meet the conditional contractor/agent criteria, possess the specific security access value, and connect during the defined 6 AM to 5 PM window.
"User/Host Profiles use a combination of attributes to identify a match. Attributes joined by OR require any one to be true, while attributes joined by AND must all be true. If a Schedule (When) is applied, the host must also connect within the specified timeframe for the profile to be considered a match. All criteria in the Who/What, Where, and When sections are cumulative." - FortiNAC-F Administration Guide: User/Host Profile Configuration.

NEW QUESTION # 20
An administrator wants to build device profiling rules based on network traffic, but the network session view is not populated with any records.
Which two settings can be enabled to gather network session information? (Choose two.)

• A. Layer 3 polling on the infrastructure devices
• B. Network traffic polling on any modeled infrastructure device
• C. Firewall session polling on modeled FortiGate devices
• D. Netflow setting on the FortiNAC-F interfaces

Answer: C,D

Explanation:
In FortiNAC-F, the Network Sessions view provides a real-time and historical log of traffic flows, including source/destination IP addresses, ports, and protocols. This data is essential for building Device Profiling Rules that rely on "Traffic Patterns" or "Network Footprints" to identify devices (e.g., an IP camera communicating with its specific NVR). If the network session view is empty, the system is not receiving the necessary flow or session data from the network infrastructure.
According to the FortiNAC-F Administration Guide, there are two primary methods to populate this view:
NetFlow/sFlow/IPFIX (C): FortiNAC-F can act as a flow collector. By enabling NetFlow settings on the FortiNAC-F service interface (port2/eth1) and configuring your switches or routers to export flow data to the FortiNAC IP, the system can parse these packets and record sessions.
Firewall Session Polling (B): For environments with FortiGate firewalls, FortiNAC-F can proactively poll the FortiGate via the REST API to retrieve its current session table. This is particularly useful as it provides session visibility without requiring the overhead of configuring NetFlow on every access layer switch.
Settings like Layer 3 Polling (D) only provide ARP table mappings (IP to MAC correlation) and do not provide the detailed flow information required for the session view.
"The Network Sessions view displays information regarding active and inactive network traffic sessions... To populate this view, FortiNAC must receive data through one of the following methods: * NetFlow/sFlow Support: Configure network devices to send flow data to the FortiNAC service interface. * Firewall Session Polling: Enable session polling on modeled FortiGate devices to retrieve session information via API. These records are then used by the Device Profiler to match rules based on traffic patterns." - FortiNAC-F Administration Guide: Network Sessions and Flow Data Collection.

NEW QUESTION # 21
Refer to the exhibit.

What will happen to the host of a guest user created from this template if the time of connection is 8:00 PM?

• A. The host will be marked as at-risk.
• B. The host will be marked as non-authenticated.
• C. The host will be administratively disabled.
• D. The host will be marked as a rogue device.

Answer: B

Explanation:
In FortiNAC-F, theGuest & Contractor Templateis a configuration object that defines the parameters for accounts created by sponsors or through self-registration. One of the critical security controls within this template is theLogin Availabilitysetting. This setting restricts the specific days and times during which a guest or contractor is permitted to authenticate and access the network.
As shown in the exhibit, the " StandardGuest " template hasLogin Availabilityset to " Specify Time " , with a schedule defined asMon-Fri, 6:00 AM to 7:00 PM. If a guest user attempts to connect or authenticate at8:00 PM, which is outside of the permitted window, FortiNAC-F ' s policy engine will automatically deny the authentication request. When an authentication attempt is denied due to schedule restrictions, the system does not move the host into the " Authenticated " or " Registered " state required for production access. Instead, the host ismarked as non-authenticatedin the adapter or host view.
This behavior ensures that even if a guest possesses valid credentials, their access is strictly bound by the organizational policy for visitor hours. The host will typically remain in its current isolation or registration VLAN, and the user will see a message on the captive portal indicating that their account is not currently authorized for login. It is important to distinguish this from " at-risk " (C), which relates to security scan failures, or " rogue " (B), which typically refers to unknown devices that have not yet been associated with a valid account or profiling rule.
" Login Availabilitydefines the timeframe during which the guest or contractor account is valid for network access. This schedule is enforced at the time of authentication. If a user attempts to log in outside of the designated window, the authentication is rejected by the system. Consequently, the host record will reflect anon-authenticatedstatus, and the device will remain restricted to the isolation or registration network until a valid login window is reached. " -FortiNAC-F Administration Guide: Guest and Contractor Templates Section.

NEW QUESTION # 22
An administrator is configuring FortiNAC-F to manage FortiGate VPN users. As part of this configuration, what is the purpose of the FortiGate firewall policy that applies to clients not yet authorized?

• A. To allow access to only the production DNS server
• B. To allow access to only the FortiNAC-F VPN interface
• C. To allow access to only the FortiGate VPN interface
• D. To allow access to only the production DNS server

Answer: B

Explanation:
The correct answer is C . The FortiNAC-F study guide explains that all VPN hosts are initially treated as unauthorized. For those unauthorized VPN hosts, the FortiGate firewall policy must allow traffic only to and from the FortiNAC-F VPN isolation interface and deny all other traffic. This forces the connecting VPN client into the FortiNAC-F validation process, including captive portal presentation and FortiNAC-F agent communication or download.
Options A and B are incorrect, and they appear duplicated in the question. The client is not supposed to be granted access only to the production DNS server while still unauthorized. FortiGate assigns DNS during VPN connection setup, with production DNS as primary and the FortiNAC-F VPN isolation interface as secondary, but the unauthorized firewall policy restricts useful access to FortiNAC-F so that validation can occur. Option D is wrong because the VPN client has already connected to the FortiGate VPN service; the authorization workflow requires access to the FortiNAC-F VPN isolation interface , not merely the FortiGate VPN interface.

NEW QUESTION # 23
When FortiNAC-F is managing VPN clients connecting through FortiGate, why must the clients run a FortiNAC-F agent?

• A. To collect the client IP address and MAC address
• B. To transparently update The client IP address upon successful authentication
• C. To validate the endpoint policy compliance
• D. To collect user authentication details

Answer: A

Explanation:
When FortiNAC-F manages VPN clients through a FortiGate, the agent plays a fundamental role in device identification that standard network protocols cannot provide on their own. In a standard VPN connection, the FortiGate establishes a Layer 3 tunnel and assigns a virtual IP address to the client. While the FortiGate sends a syslog message to FortiNAC-F containing the username and this assigned IP address, it typically does not provide the hardware (MAC) address of the remote endpoint's physical or virtual adapter.
FortiNAC-F relies on the MAC address as the primary unique identifier for all host records in its database. Without the MAC address, FortiNAC-F cannot correlate the incoming VPN session with an existing host record to apply specific policies or track the device's history. By running either a Persistent or Dissolvable Agent, the endpoint retrieves its own MAC address and communicates it directly to the FortiNAC-F service interface. This allows the "IP to MAC" mapping to occur. Once FortiNAC-F has both the IP and the MAC, it can successfully identify the device, verify its status, and send the appropriate FSSO tags or group information back to the FortiGate to lift network restrictions.
Furthermore, while the agent can also perform compliance checks (Option D), the architectural requirement for the agent in a managed VPN environment is primarily driven by the need for session data correlation-specifically the collection of the IP and MAC address pairing.
"Session Data Components: * User ID (collected via RADIUS, syslog and API from the FortiGate). * Remote IP address for the remote user connection (collected via syslog and API from the FortiGate and from the FortiNAC agent). * Device IP and MAC address (collected via FortiNAC agent). ... The Agent is used to provide the MAC address of the connecting VPN user (IP to MAC)." - FortiNAC-F FortiGate VPN Integration Guide: How it Works Section.

NEW QUESTION # 24
How can an administrator configure FortiNAC-F to normalize incoming syslog event levels across vendors?

• A. Configure the vendor OUI settings.
• B. Configure the security rule settings.
• C. Configure event to alarm mappings.
• D. Configure severity mappings.

Answer: D

Explanation:
FortiNAC-F serves as a central manager for security events originating from a diverse ecosystem of third- party security appliances, such as FortiGate, Check Point, and Cisco. Each vendor utilizes its own internal scale forseverity levelswithin syslog messages (e.g., Check Point uses a 1-5 scale, while others may use 0-7).
To provide a consistent response regardless of the source, FortiNAC-F usesSeverity Mappingsto normalize these incoming values.
According to theFortiNAC-F Administration Guide, severity mappings allow the administrator to translate vendor-specific threat levels into standardizedFortiNAC Security Levels(such as High, Medium, or Low Violation). When a syslog message arrives, the parser extracts the vendor ' s severity code, and the system immediately references theSecurity Event Severity Level Mappingstable to determine how that event should be categorized internally. This normalization is vital because it allows a singleSecurity Alarmto be configured to respond to any " High Violation " event, whether it was reported as a " Critical " by one vendor or a " Level
5 " by another. Without these mappings, the administrator would have to create separate, redundant security rules for every vendor to account for their different naming conventions and numerical scales.
" Each vendor defines its own severity levels for syslog messages. The following table shows the equivalent FortiNAC security level... To normalize these events, configure theSeverity Level Mappingsfound in the device integration guides. This allows FortiNAC to generate a consistent security event that can then trigger an alarm regardless of the reporting vendor ' s specific terminology. " -FortiNAC-F Administration Guide:
Vendor Severity Levels and Syslog Management.

NEW QUESTION # 25
Refer to the exhibit.

An administrator wants to use FortiNAC-F to automatically provision printers throughout their organization.
Each building uses its own local VLAN for printers.
Which FortiNAC-F feature would allow this to be accomplished with a single network access policy?

• A. Logical networks
• B. Preferred VLAN designations
• C. Dynamic host groups
• D. Device profiling rules

Answer: A

Explanation:
The FortiNAC-FLogical Networkfeature is specifically designed to provide an abstraction layer between high- level security policies and the underlying physical network infrastructure. In large-scale deployments where different physical locations (like Building 1, 2, and 3 in the exhibit) use different local VLAN IDs for the same type of device (e.g., VLAN 10, 20, and 30 for printers), managing separate policies for each building would create significant administrative overhead.
By using aLogical Network, an administrator can create a single entity-for example, a logical network named " Printers " -and use it as the " Access Value " in a singleNetwork Access Policy. The mapping of this logical label to a specific physical VLAN occurs at theModel Configurationlevel for each network device.
When a printer connects to a switch in Building 1, FortiNAC-F evaluates the policy, identifies that the printer should be in the " Printers " logical network, and checks the Model Configuration for that specific switch to see which VLAN ID is mapped to that label (VLAN 10). If the same printer moves to Building 3, the same single policy applies, but FortiNAC-F provisions it to VLAN 30 based on the local mapping for that building ' s switch.
This architectural approach ensures that policies remain consistent and easy to manage regardless of the complexity or variations in the local network topology.
" Logical Networks provide a way to define a network access requirement once and apply it across many different network devices that may use different VLAN IDs for that access... Each managed device can usedifferent VLAN IDs for the same Logical Network label. You can define the Logical Networks based on requirements and then associate the network to a VLAN ID when the managed device is configured in theModel Configuration. " -FortiNAC-F IoT Deployment Guide: Define the Logical Networks.

NEW QUESTION # 26
Two FortiNAC-F devices have been configured as a 1 + 1 HA pair. The primary server went offline and a successful failover to the secondary has occurred. What happens if the primary server comes back online?

• A. The primary server will determine that the secondary has control and power down for maintenance.
• B. The primary and secondary servers will resume communication and the secondary will maintain control.
• C. The secondary server will update the primary and the servers will load balance until an administrator forces the primary to resume full control.
• D. After five successful heartbeats between the servers, the primary server will resume control.

Answer: B

Explanation:
The correct answer is A . In a FortiNAC-F 1+1 HA deployment, failover from primary to secondary is automatic, but failback to the primary is not automatic . The study guide states that if the primary device or its network connectivity fails, the secondary assumes control automatically, but restoration of a failed-over HA deployment is a manual administrator-driven process. It further explains that after the cause of the failover is resolved, the administrator must use the Resume Control button to transfer control back to the primary server.
That means when the primary comes back online, it does not immediately take over again. The pair can resume HA communication, but the secondary remains the in-control node until an administrator deliberately returns control to the primary. Option B is wrong because FortiNAC-F 1+1 HA is active-passive, not load- balanced. Option C is wrong because the restored primary does not power itself down for maintenance.
Option D is a trap: five failed heartbeats are used in failure detection and gateway validation logic, not as an automatic failback timer. The exam point is simple: automatic failover, manual failback .

NEW QUESTION # 27
As part of a company policy, all end stations must be scanned for compliance each day. The security administrators want to satisfy this requirement without any necessary interaction from the end user. Which two agents can provide that functionality? (Choose two.)

• A. Mobile
• B. Persistent
• C. Dissolvable
• D. Passive

Answer: B,D

Explanation:
The correct answers are B and C . The persistent agent is the strongest fit because it is installed and stays resident on the endpoint. The study guide states that after deployment, the persistent agent communicates back to FortiNAC-F every 15 minutes and performs scheduled scans in the background, transparent to the end user. That directly satisfies the requirement for recurring compliance scans without user involvement.
The passive agent can also scan Windows domain end stations without end-user interaction. The guide states that the passive agent is deployed through login/logoff scripts and administrative templates, and that passive agent registration can register and scan hosts associated with LDAP or Active Directory users. If enabled, the passive agent scans the host to verify compliance with the appropriate endpoint policy.
Option A is wrong because the dissolvable agent is a run-once agent that requires manual end-user interaction in the captive portal, then removes itself after reporting results. Option D is not the best answer for this requirement because the mobile agent is specifically for Android onboarding and is manually installed; it is not the general solution for daily compliance scanning of all end stations.

NEW QUESTION # 28
Refer to the exhibit.

What would FortiNAC-F generate if only one of the security fitters is satisfied?

• A. A normal alarm
• B. A normal event
• C. A security alarm
• D. A security event

Answer: B

Explanation:
In FortiNAC-F, Security Triggers are used to identify specific security-related activities based on incoming data such as Syslog messages or SNMP traps from external security devices (like a FortiGate or an IDS). These triggers act as a filtering mechanism to determine if an incoming notification should be escalated from a standard system event to a Security Event.
According to the FortiNAC-F Administrator Guide and relevant training materials for versions 7.2 and 7.4, the Filter Match setting is the critical logic gate for this process. As seen in the exhibit, the "Filter Match" configuration is set to "All". This means that for the Security Trigger named "Infected File Detected" to "fire" and generate a Security Event or a subsequent Security Alarm, every single filter listed in the Security Filters table must be satisfied simultaneously by the incoming data.
In the provided exhibit, there are two filters: one looking for the Vendor "Fortinet" and another looking for the Sub Type "virus". If only one of these filters is satisfied (for example, a message from Fortinet that does not contain the "virus" subtype), the logic for the Security Trigger is not met. Consequently, FortiNAC-F does not escalate the notification. Instead, it processes the incoming data as a Normal Event, which is recorded in the Event Log but does not trigger the automated security response workflows associated with security alarms.
"The Filter Match option defines the logic used when multiple filters are defined. If 'All' is selected, then all filter criteria must be met in order for the trigger to fire and a Security Event to be generated. If the criteria are not met, the incoming data is processed as a normal event. If 'Any' is selected, the trigger fires if at least one of the filters matches." - FortiNAC-F Administration Guide: Security Triggers Section.

NEW QUESTION # 29
When creating a user or host profile, which three criteria can you apply? (Choose three.)

• A. An applied access policy
• B. Adapter current VLAN
• C. Host or user group memberships
• D. Host or user attributes
• E. Location

Answer: C,D,E

Explanation:
The User/Host Profile is the primary mechanism in FortiNAC-F for identifying and categorizing endpoints to determine their level of network access. According to the FortiNAC-F Administration Guide, a profile is built using a combination of criteria that define "Who" is connecting, "What" device they are using, and "Where" they are located on the network.
The three main categories of criteria available in the configuration are:
Host or User Attributes (B): This includes specific details such as the host's operating system, the user's role (e.g., Employee, Contractor), or custom attributes assigned to the record.
Host or User Group Memberships (A): Profiles can be configured to match endpoints that are members of specific internal FortiNAC groups or synchronized directory groups (like LDAP or Active Directory groups). This allows for broad policy application based on organizational structure.
Location (E): The "Where" component allows administrators to restrict a profile match to specific physical or logical areas of the network, such as a particular switch, a group of ports, or a specific SSID.
Criteria like an "applied access policy" (D) are the outcome of a profile match rather than a criterion used to define the profile itself. Similarly, the "Adapter current VLAN" (C) is a dynamic state that changes based on enforcement and is not a standard static identifier used for profile matching.
"User/Host Profiles are used to identify the hosts and users to which a policy will apply. Profiles are created by selecting various criteria in the Who/What (Attributes and Groups) and Where (Locations) sections. Attributes can include Host Role, User Role, and OS. Group memberships allow matching based on internal or directory-based groups. Location criteria allow for filtering based on the device or port where the host is connected." - FortiNAC-F Administration Guide: User/Host Profile Configuration.

NEW QUESTION # 30
Where should you configure MAC notification traps on a supported switch?

• A. Only on ports defined as learned uplinks
• B. Only on ports that generate linkup and linkdown traps
• C. On all ports except uplink ports
• D. On all ports on the switch

Answer: C

Explanation:
In FortiNAC-F, MAC notification traps (also known as MAC Move or MAC Change traps) are essential for achieving real-time visibility of endpoint connections and disconnections. When a device connects to a switch port, the switch generates an SNMP trap that informs FortiNAC-F of the new MAC address on that specific interface. This allows FortiNAC-F to immediately initiate the profiling and policy evaluation process without waiting for the next scheduled L2 poll.
According to the FortiNAC-F Administration Guide and Switch Integration documentation, MAC notification traps should be configured on all ports except uplink ports. Uplink ports are the interfaces that connect one switch to another or to the core network. Because these ports see the MAC addresses of every device on the downstream switches, enabling MAC notification on uplinks would cause the switch to send a massive volume of redundant traps to FortiNAC-F every time any device anywhere in the downstream branch moves or reconnects. This can overwhelm the FortiNAC-F process queue and degrade system performance.
By only enabling these traps on "edge" or "access" ports-where individual endpoints like PCs, printers, and VoIP phones connect-FortiNAC-F receives precise data regarding exactly where a device is physically located. Uplinks should be identified in the FortiNAC-F inventory as "Uplink" or "Learned Uplink," which tells the system to ignore MAC data seen on those specific ports.
"To ensure accurate host tracking and optimal system performance, SNMP MAC notification traps must be enabled on all access (downlink) ports. Do not enable MAC notification traps on uplink ports, as this will result in excessive and unnecessary trap processing. Uplink ports should be excluded to prevent the system from attempting to map multiple downstream MAC addresses to a single infrastructure interface." - FortiNAC-F Administration Guide: SNMP Configuration for Network Devices.

NEW QUESTION # 31
Refer to the exhibit.

What will happen to the host of a guest user created from this template if the time of connection is 8:00 PM?

• A. The host will be marked as at-risk.
• B. The host will be marked as non-authenticated.
• C. The host will be administratively disabled.
• D. The host will be marked as a rogue device.

Answer: B

Explanation:
In FortiNAC-F, the Guest & Contractor Template is a configuration object that defines the parameters for accounts created by sponsors or through self-registration. One of the critical security controls within this template is the Login Availability setting. This setting restricts the specific days and times during which a guest or contractor is permitted to authenticate and access the network.
As shown in the exhibit, the "StandardGuest" template has Login Availability set to "Specify Time", with a schedule defined as Mon-Fri, 6:00 AM to 7:00 PM. If a guest user attempts to connect or authenticate at 8:00 PM, which is outside of the permitted window, FortiNAC-F's policy engine will automatically deny the authentication request. When an authentication attempt is denied due to schedule restrictions, the system does not move the host into the "Authenticated" or "Registered" state required for production access. Instead, the host is marked as non-authenticated in the adapter or host view.
This behavior ensures that even if a guest possesses valid credentials, their access is strictly bound by the organizational policy for visitor hours. The host will typically remain in its current isolation or registration VLAN, and the user will see a message on the captive portal indicating that their account is not currently authorized for login. It is important to distinguish this from "at-risk" (C), which relates to security scan failures, or "rogue" (B), which typically refers to unknown devices that have not yet been associated with a valid account or profiling rule.
"Login Availability defines the timeframe during which the guest or contractor account is valid for network access. This schedule is enforced at the time of authentication. If a user attempts to log in outside of the designated window, the authentication is rejected by the system. Consequently, the host record will reflect a non-authenticated status, and the device will remain restricted to the isolation or registration network until a valid login window is reached." - FortiNAC-F Administration Guide: Guest and Contractor Templates Section.

NEW QUESTION # 32
An administrator wants each department to create and manage its own contractor accounts but not be able to manage contractor accounts for other departments. What must the administrator configure to limit the sponsor
' s capabilities?

• A. The sponsor ' s administrative profile
• B. The user/host profile applied to the contractor
• C. The contractor ' s template
• D. The portal settings on the kiosk portal page

Answer: A

Explanation:
The correct answer is D . FortiNAC-F limits what a sponsor can create and manage through the administrator profile assigned to that sponsor. The study guide explains that sponsors can be restricted to specific guest or contractor templates and that the Manage Guests settings in the admin profile define whether the sponsor can manage all accounts, no accounts, or only accounts they created. It also states that allowed templates are defined in the admin profile, meaning each department can be given access only to its own contractor template.
The contractor template defines account fields, role values, authentication method, account duration, and related account properties, but it does not by itself restrict what a sponsor can manage. Portal settings control how users interact with the captive portal or kiosk page, not sponsor administrative scope. A user/host profile is used for matching users or hosts in policy decisions; it does not delegate sponsor permissions. For departmental separation, the administrator must create sponsor-specific administrative profiles that allow only the appropriate templates and account-management scope.

NEW QUESTION # 33
Refer to the exhibits.

What would happen if the highlighted port with connected hosts was placed in both the Forced Registration and Forced Remediation port groups?

• A. Only the higher ranked enforcement group would be applied.
• B. Multiple enforcement groups could not contain the same port.
• C. Both types of enforcement would be applied
• D. Enforcement would be applied only to rogue hosts

Answer: A

Explanation:
In FortiNAC-F, Port Groups are used to apply specific enforcement behaviors to switch ports. When a port is assigned to an enforcement group, such as Forced Registration or Forced Remediation, FortiNAC-F overrides normal policy logic to force all connected adapters into that specific state. The exhibit shows a port (IF#13) with "Multiple Hosts" connected, which is a common scenario in environments using unmanaged switches or hubs downstream from a managed switch port.
According to the FortiNAC-F Administrator Guide, it is possible for a single port to be a member of multiple port groups. However, when those groups have conflicting enforcement actions-such as one group forcing a registration state and another forcing a remediation state-FortiNAC-F utilizes a ranking system to resolve the conflict. In the FortiNAC-F GUI under Network > Port Management > Port Groups, each group is assigned a rank. The system evaluates these ranks, and only the higher ranked enforcement group is applied to the port. If a port is in both a Forced Registration group and a Forced Remediation group, the group with the numerical priority (rank) will dictate the VLAN and access level assigned to all hosts on that port.
This mechanism ensures consistent behavior across the fabric. If the ranking determines that "Forced Registration" is higher priority, then even a known host that is failing a compliance scan (which would normally trigger Remediation) will be held in the Registration VLAN because the port-level enforcement takes precedence based on its rank.
"A port can be a member of multiple groups. If more than one group has an enforcement assigned, the group with the highest rank (lowest numerical value) is used to determine the enforcement for the port. When a port is placed in a group with an enforcement, that enforcement is applied to all hosts connected to that port, regardless of the host's current state." - FortiNAC-F Administration Guide: Port Group Enforcement and Ranking.

NEW QUESTION # 34
What must an administrator configure to allow FortiNAC-F to process incoming syslog messages that are not supported by default?

• A. A Log Receiver
• B. A Security Action
• C. A Syslog Service Connector
• D. A Security Event Parser

Answer: D

Explanation:
FortiNAC-F provides a robust engine for processing security notifications from third-party devices. For standard integrations, such as FortiGate or Check Point, the system comes pre-loaded with templates to interpret incoming data. However, when an administrator needs FortiNAC-F to process syslog messages from a vendor or device that is not supported by default, they must configure a Security Event Parser.
The Security Event Parser acts as the translation layer. It uses regular expressions (Regex) or specific field mappings to identify key data points within a raw syslog string, such as the source IP address, the threat type, and the severity. Without a parser, FortiNAC-F may receive the syslog message but will be unable to "understand" its contents, meaning it cannot generate the necessary Security Event required to trigger automated responses. Once a parser is created, the system can extract the host's IP address from the message, resolve it to a MAC address via L3 polling, and then apply the appropriate security rules. This allows for the integration of any security appliance capable of sending RFC-compliant syslog messages.
"FortiNAC parses the information based on pre-defined security event parsers stored in FortiNAC's database... If the incoming message format is not recognized, a new Security Event Parser must be created to define how the system should extract data fields from the raw syslog message. This enables FortiNAC to generate a security event and take action based on the alarm configuration." - FortiNAC-F Administration Guide: Security Event Parsers.

NEW QUESTION # 35
Which two statements are true about integrating a third-party device using SNMP traps from that device as input to generate an event? (Choose two.)

• A. The sending device must be modeled in the inventory topology.
• B. set allowaccess snmp must be configured using the CLI on the FortiNAC-F receiving interface.
• C. The IP address OID and MAC address OID must be configured in the trap MIB file.
• D. The sending device must support SNMPv3.

Answer: A,B

Explanation:
The correct answers are A and C . Fortinet's FortiNAC-F 7.6 documentation states that, to receive and interpret traps from devices or applications, those devices or applications must be modeled in FortiNAC and must have an associated IP address. That validates option A directly. The same Fortinet Trap MIB Files documentation also lists a FortiNAC-OS requirement: the snmp option must be included in the set allowaccess command. That validates option C .
Option B is wrong because Trap MIB integration is not limited to SNMPv3. Fortinet states that Trap MIB supports receiving SNMPv1 and SNMPv2 traps from external devices, while SNMPv3 is discussed separately for traps that populate host and user records.
Option D is the trap. The Fortinet documentation explicitly says IP address OID, MAC address OID, and user ID OID are not all required ; any one OID can be used to identify the host or user that triggered the trap. So the statement that both the IP address OID and MAC address OID must be configured is false.

NEW QUESTION # 36
Refer to the exhibit.

Given this topology, and a layer 3 registration network configuration, which IP address would be designated in the DHCP relay configuration for the registration network?

• A. 192.168.10.254
• B. 192.168.100 75
• C. 192.168.200.10
• D. 192.168.100.20

Answer: C

Explanation:
The correct answer is D . In a Layer 3 registration or isolation network design, DHCP requests from the isolated registration VLAN are not served locally on that VLAN by a normal production DHCP server.
Instead, the registration VLAN's DHCP relay must forward DHCP traffic to FortiNAC-F port2 , because port2 is the captive network service interface. The study guide states that in Layer 3 captive networks, DHCP traffic is relayed to port2 from the captive networks, and that the FortiNAC-F port2 interface provides DHCP, DNS, and captive portal services for hosts assigned to those captive networks.
In the exhibit, the registration VLAN is 192.168.10.x/24 , with gateway 192.168.10.254 . That gateway is where the DHCP relay would be configured, but it is not the relay destination. The relay destination must be the FortiNAC-F port2 address, shown as 192.168.200.10 . The corporate DHCP server 192.168.100.75 is for production network addressing, not registration isolation. The FortiNAC-F port1 address 192.168.100.20 is the administrative or production-facing interface, not the captive network service interface. Therefore, the DHCP relay should point to 192.168.200.10 .

NEW QUESTION # 37
Refer to the exhibits.


Based on the given configurations and settings, on which date and time would a guest account created at 8:00 AM on 2025/09/12 expire?

• A. 2025/09/12 at 17:00:00
• B. 2025/09/12 at 7:00 PM
• C. 2025/09/13 at 17:00:00
• D. 2025/09/12 at 8:00 PM

Answer: C

Explanation:
Questio ns no: 22
Verified Answe r: D
Comprehensive and Detailed 250 to 300 words each Explanation with Exact Matched Extract from FortiNAC-F Administrator library and documentation for current versions (including F 7.2, 7.4, and 7.6) documents:
In FortiNAC-F, the expiration of a guest or contractor account is determined by the configuration settings within the Account Creation Wizard and the associated Guest/Contractor Template. While a template can define a default "Account Duration" (as seen in the 12-hour setting in the second exhibit), the Account Creation Wizard allows an administrator to manually specify or override the start and end parameters for a specific user session.
According to the FortiNAC-F Administration Guide regarding guest management, the Account End Date field in the creation wizard is the definitive timestamp for when the account object will be disabled or deleted from the system. In the provided exhibit (Account Creation Wizard), the administrator has explicitly set the Account Start Date to 2025/09/12 08:00:00 and the Account End Date to 2025/09/13 17:00:00.
Even though the template indicates an "Account Duration" of 12 hours, this value typically serves as a pre-populated default. When a manual date and time are entered into the wizard, those specific values take precedence for that individual account. The account will remain active and valid until 5:00 PM (17:00:00) on the following day, 2025/09/13. It is also important to note the "Login Availability" from the template (8:00 AM - 7:00 PM); while the account exists until the 13th at 17:00:00, the user would only be able to authenticate during the active hours defined by the login schedule on both days.
"When creating an account, the administrator can select a template to provide default settings. However, specific values such as the Account End Date can be modified within the Account Creation Wizard. The date and time specified in the 'Account End Date' field determines the absolute expiration of the account. Once this time is reached, the account is moved to an expired state and the user's network access is revoked." - FortiNAC-F Administration Guide: Guest and Contractor Account Management.

NEW QUESTION # 38
......

Authentic NSE5_FNC_AD_7.6 Dumps With 100% Passing Rate Practice Tests Dumps: https://testking.prep4sureexam.com/NSE5_FNC_AD_7.6-dumps-torrent.html